...

How to Read a CNC Machining Quote

5-Axis Milled Aluminum Part with Hard Black Anodizing Finish

A CNC quote is not one number. It is a fixed cost plus a per-part cost, multiplied by your quantity. Split every quote into those two parts before you compare anything: ask for the total at two or three quantities, and the gap between the totals tells you which part of the price is fixed and which part moves with quantity. Then change one driver at a time — quantity, tolerance, material, or finish — and ask what each change saves. The cheapest quote is usually the one whose fixed cost is spread over the most parts, not the one with the lowest unit price at your smallest quantity.

That split is the whole method. Below: where each line comes from, how to run the two-quantity test, why one piece costs what it does, what MOQ means, and which quotes not to trust.

The short answer: split every quote into fixed cost and per-part cost

Fixed cost is paid once per job — programming, setup, proving the first part. Per-part cost is paid again for every piece — material, cutting minutes, finishing, inspection.

The unit price is the fixed cost divided by your quantity, plus the per-part cost. That is why the same part can cost several times as much per piece at 10 pieces as at 100, with no change to the part at all. The part did not get cheaper. The fixed cost just got spread thinner. So never compare two quotes on unit price alone. Compare totals at the same quantity, then ask each supplier for the total at a second quantity. Two totals show the shape of the price. One total tells you nothing about it.

The 5 lines behind a quote

A quote is a price for a specific drawing, at a specific quantity, with specific assumptions. The money goes to five places.

Material is the raw stock — alloy, form, and blank size — plus the waste. Ask which alloy and temper are priced.

Programming and setup is writing the program, setting the fixture, and proving the first part. It is the biggest fixed cost on a small order, paid once and then divided by the quantity.

Machining time is the minutes the machine spends cutting each piece. A deep pocket, a tight tolerance, or a feature on a second face adds minutes to every piece.

Finishing — anodizing, blasting, plating, polishing, paint — is usually a per-part cost, often a separate line. Ask whether it is included.

Inspection is measuring the part against the drawing: first-article inspection, material certificates, dimensional reports. It can be fixed or per-part. Ask what documents you receive, and whether they are in the price. A quote that leaves inspection out is not cheaper, it is incomplete.

A good quote names its assumptions for all five. If a line is missing, the supplier left it out.

The two-quote test: solve for fixed vs per-part cost from quantity breaks

The method needs only two totals from the same supplier, for the same part, at two different quantities. Write the total as: Total = fixed cost + (per-part cost × quantity). The difference between the two totals, divided by the difference in quantity, is the per-part cost. Subtract that from either total and you have the fixed cost.

Read the shape. If the total barely moves when the quantity goes up tenfold, the price is mostly fixed cost, and ordering more brings the unit price down fast. If the total rises almost in proportion to the quantity, the price is mostly per-part cost, and ordering more will not help much. If two suppliers match at 10 pieces but differ at 100, the one whose price falls faster is cheaper at volume.

Ask for the totals at 10, 50, and 100 pieces. One warning: this test only works on totals for the same part, from the same supplier, with the same assumptions. Check the assumptions first, then run the test.

Why a 1-piece quote looks expensive — and when that is correct

A single piece carries the whole fixed cost by itself: the programming, the setup, the first-article inspection. So a one-piece quote can easily be several times the unit price at 100 pieces, and that is not a trick. It is arithmetic.

It is correct when the fixed cost is real. It is a warning sign when the fixed cost is not explained — ask the supplier to name the fixed cost and the per-part cost separately.

There are two cases where a one-piece quote should not be expensive. The first is when the part is simple, the program already exists, and the setup is trivial. The second is when the prototype will go into production on the same program and fixture: the fixed cost is an investment in the next order, not a cost to be recovered from one piece. Ask whether that is the case. The practical rule: never judge a supplier on a one-piece price. Judge it on the total at the quantity you will actually order.

What drives the price up: tolerance, setups, material, finish

Four drivers do most of the damage. The most expensive is usually tolerance: ±0.01 mm on a feature that only needs ±0.1 mm buys slower machining, more inspection, and more scrap. Tighten only the features that matter and let the rest run at the general tolerance class.

The second is setups: every time the part is taken out, turned over, and re-fixtured, you pay for the setup and for the risk the next face does not line up. Move a feature onto a face already being machined to save a setup on every piece.

The third is material: the alloy sets the price of the blank and the machining time. Do not specify a premium alloy for a part a standard one would serve.

The fourth is finish: a finish applied to the whole part costs more than one applied only where it is needed, and masking costs more again. Ask what the finish actually protects, and whether a simpler surface treatment would do.

Precision CNC-machined aluminum cylindrical housings with bored holes and finished metal surfaces, with black anodized parts in the foreground

The comparison table: what each cost driver does

Use this table to trade one driver against another.

Cost driverWhat it isHow it shows up in the quoteHow to lower it (and what you give up)
Setup / programmingProgram, fixture, first pieceFixed cost, once per jobOrder more, or reuse an existing program
Cycle timeMinutes cutting each piecePer-part cost; grows with pockets, holes, extra facesSimplify the geometry
MaterialRaw stock: alloy, temper, blank sizePer-part cost; blank and waste both pricedStandard alloy, or a blank closer to finished size
ToleranceHow tightly each feature is heldPer-part cost, rising steeply as the band narrowsTighten only features that matter
FinishAnodizing, blasting, plating, polishing, paintPer-part cost, often a separate lineFinish only where needed, or a simpler finish
InspectionFirst-article reports, certificates, dimensional reportsFixed for the report; per-part for measuring piecesMatch inspection to risk
QuantityHow many pieces you orderSpreads fixed cost thinner; unit price falls, then flattensOrder at a quantity break

MOQ, honestly: what it is, what it is not, and why “no MOQ” does not mean the same unit price

MOQ — minimum order quantity — is the smallest order a supplier will accept. It is a policy, not a law of physics: below a certain quantity, the fixed cost makes the unit price so high that neither side is happy.

What it is: a floor on the order, set where the fixed cost stops dominating the price. It is not a promise about the unit price. A supplier with “no MOQ” still charges the full fixed cost on a one-piece order — the unit price is simply high, because one piece carries it all.

Ask the supplier directly, in writing: is there a minimum order quantity, and what is the unit price at that quantity and above it? If there is no MOQ, ask for the unit price at 1, 10, and 100 pieces.

Tenghui’s published order range is 10 to 10,000+ pieces — a range the shop works in, not a minimum order quantity. Do not read “10” as an MOQ.

Quantity breaks: where the price actually drops, and where it flattens

A quantity break is a quantity at which the unit price steps down — because the fixed cost is now spread over enough pieces, or the shop changes how it makes the part.

The price drops fastest at the start. Going from 1 piece to 10, the unit price can fall by most of the fixed cost in that step. From 10 to 100 the gain is smaller, and from 100 to 1,000 smaller still — by then the price is mostly per-part cost, which does not fall with quantity. That is the flattening: ordering more stops helping, and the only way to cut the price further is to change the part.

Ask the supplier where the breaks are, and what changes at each one. A break from spreading fixed cost is free money — take it if you can use the parts. A break the supplier cannot explain is not a break; it is a number it made up.

For high-volume production, the question is where the price flattens, and whether the flattened price is one you can live with.

Red flags in a quote (lump sum only, no quantity breaks, tolerance assumptions unstated)

  • A single lump-sum number, with no breakdown and no assumptions. You cannot tell what you are paying for.
  • No prices at more than one quantity. The supplier is hiding the shape of its price.
  • Tolerance assumptions unstated. If the quote does not say which tolerance it priced, it priced the easiest one.
  • Material unstated, or “aluminium” with no alloy or temper. That quote has not priced your part.
  • Finish unstated, or “anodized” with no type or thickness. The finish changes the price and the dimensions.
  • No expiry date. Material prices move.
  • A quote far below everyone else, with no explanation. Somebody priced a different part. Ask what was left out.
  • A quote that arrives with no questions at all. A supplier that quotes a complex part without a single question has not read your drawing.

One red flag is a warning. Two are a pattern. Three mean you should shortlist someone else — start with the guide on choosing a CNC machining supplier in China before your next RFQ.

Procurement judgment

Do not accept a quote you cannot split. Ask for the total at two or three quantities, read the fixed cost off the shape, and change one driver at a time — quantity first, then tolerance, then material, then finish. The driver that saves the most without breaking the part is the one to change.

Then judge the quote on its clarity, not only on its number. A clear quote is a supplier you can work with. A vague quote is a supplier that will be vague when the part is late.

If you have a quote in hand now, send Tenghui your drawing and ask for the same breakdown at two or three quantities — the totals will show you the fixed cost at once. Orders run from 10 to 10,000+ pieces, single prototypes to repeat production, with material and finishing to match the part, from a Dongguan shop with 13 years of custom CNC machining experience, for customers in automation equipment, optical systems, and scientific instruments. Contact Tenghui for a quote — usually within 24 hours.

Frequently asked questions

1. Why is the cheapest quote not always the cheapest part? Because the cheapest quote is often the one that priced a different part: a looser tolerance, a cheaper material, a missing finish, or no inspection. The part you actually need costs what it costs, and the quote that left something out will collect the difference later — in rework, in scrap, in a part that does not fit, or in a second order from a supplier that priced it properly the first time. Compare totals at the same quantity, with the same assumptions. That is the real price.

2. Should I ask for a quote at 10, 50 and 100 pieces? Yes, if those are quantities you might actually order. Three totals show the shape of the price: where it falls fast, and where it flattens. They also show whether two suppliers who look identical at 10 pieces are actually different at 100. Do not ask for quantities you will never order — a quote at 10,000 pieces is useless if you need 50 — but do ask for the quantities either side of the one you expect.

3. Does “no MOQ” mean I can order 1 piece at the 1,000-piece price? No. “No MOQ” means the supplier will accept a one-piece order. It does not change the arithmetic: on one piece, the fixed cost — programming, setup, first-article inspection — lands on that single piece, so the unit price is high. At 1,000 pieces the same fixed cost is spread over a thousand pieces, so the unit price is low. The policy decides whether you may order; the quantity decides what you pay.

Facebook
Pinterest
Twitter
LinkedIn

Newsletter

Sign up our newsletter to get update information, news and free insight.

Send Us a Message

Once we receive your design files, our senior manufacturing engineers will manually perform a comprehensive DFM review and deliver an accurate, optimized quote within 24 hours.